Sunday, October 30, 2016

Pulling the Stuff Out of My Head

Hi All,
It has been a while since I last sat down and shared stuff with you, but I want you to know that it has not been for lack of stuff happening or lack of thinking about sharing. Time has just been flying by.

Today though, I am hoping to share something that may be of interest to some of you and useful...especially as we approach the holiday season.

For several years I have added a stretched and mounted quilt finishing method to the others I use. Once completed these pieces hang nicely on the wall as would any framed art item.

The quilting remains the same.... though if I know I am planning to mount a piece my backing fabric does not have to be anything fancy, for it will not be seen. Once the top is done, I create my quilt sandwich and quilt and embellish the piece. With the piece done the mounting process begins by first selecting the size pine wood you want for your frame (I use 1x2s-but note these are not really 1"x2"-more 3/4"x1 1/2") then:

1. Trim the quilt to the size desired.
2. Cut binding strips. (for the 1x2's I use 3" wide straight of grain binding strips)
3. Attach the binding as 4 separate strips. 1 to each edge of the quilt. Starting 1/4" from each edge. Leaving about an extra inch unstitched on each side.
4. With all the sides stitched into place I fold back each corner, right sides together, matching the binding edges. This creates a 45 degree angle on the quilt edge and lines the the binding up below. From that corner point of the quilt edge I drawn a line straight down to binding edge.
5. Once it is lined up, line drawn I stitch on the line, then trim it back to 1/4". Repeat on each corner, and turn the corners out to complete.
With the corners done, I move on to building the frame.

1. Measure the inside dimensions of the prepared quilt. Note the measurements of the width and length.
2. Cut width pieces of wood to the dimension noted.
3. Take 1 1/2" off the length dimension (for 1x2s), and cut length pieces to this size.
4. Line up frame pieces widths to the outside with lengths on the inside to create the corners. Use wood glue and nails to hold frame together.

For the mounting and stretching:
1. Cut batting approximately 3"s bigger than frame all around.
2. With batting on flat surface, place frame in middle and starting in the center of each side stretch batting around the frame, while either gluing or stapling in place.
3. Lastly, slip quilt over the batting covered side of frame, and again working from center of each side stretch the binding around frame and staple in place.

If desired, a backing can be made and glued in place over the back before adding hanging hardware as below.


Then they are ready to hang and enjoy!!!!






8 comments:

  1. Thanks for the post. I really liked your wall hanging and was wondering about the process.
    LauraT

    ReplyDelete
    Replies
    1. thanks Laura -- the process for making the quilts themselves is my Fast-Piece Applique -- the inspiration for the designs came from leaves and feathers

      Delete
  2. I think the way you display your work is absolutely the best! It's elegant, stands on its own, will go with any other decor elements, portable, and on and on... :) Will share on TAFA soon!

    ReplyDelete
    Replies
    1. Thanks Rachel! You should know since you have seem all this stuff up around my house up close and personal.

      Delete
  3. Thanks for sharing this helful tutorial. I will save this for a future quilt.

    ReplyDelete
  4. I hope you have a chance to try it out, for it works really well. ~Rose

    ReplyDelete
  5. Is there something we should know about quilting with silk? Needle size, stitch length..stuff like that. This design is a real wow-zer. Thanks

    ReplyDelete
    Replies
    1. I talk about using silk in my last book 'Fast Piece Applique', but the most important thing to remember is to always back the silk with a very lightweight iron-on interfacing before stitching. This will keep the silk from slipping and fraying as only silk can. Once prepared you can treat it like any other cotton, and that includes sewing it to cotton. Hope this helps

      Delete